Plastic Slab Bolster

  • Available heights –  ¾” / 1” / 1.25” / 1.5” / 1.75” / 2” / 2.25” / 2.5” / 2.75” / 3”
  • 30” lengths
  • Slab Bolsters can be extended to longer lengths through its snapped locking system
  • The pointed tips allow minimum point of surface contact
  • Ideal for pouring precast, garage parking decks, tilt-up and other structures that require  additional rebar reinforcement

Grade Chair with Base

  • Each chair comes with two height options
  • Available heights – 1.5”-2”/ 2"-2.5”/ 2.5"-3”/ 3"-3.5”/ 3.5”-4”
  • Max bar size #6
  • 300 lbs. load bearing
  • Wide base allows for solid footing

F-Chair

  • Chair comes with two height options
  • Available heights – ¾”/ 1”
  • Max bar size #6
  • Wide base allows for solid footing

H-Chair-6 Leg

  • Available heights – 1”, 1.5” / 2” / 2.5” / 3” / 3.5” / 4” / 4.5” / 5”, 5.5” / 6”
  • Max bar size #11
  • 800 lbs. Load Bearing
  • Unbeatable design, strong and stable, due to that the same axel has two points for bar support
  • Suggested for multiple applications – concrete slabs, precast, tilt-up and concrete finish

H-Chair-4 Leg

  • Available heights – 1.5” / 2” / 2.5” / 3” / 3.5” / 4”
  • Max bar size #11
  • 600 lbs. load bearing
  • Unbeatable design, strong and stable, due to that the same axel has two points for bar support
  • Suggested for multiple applications – concrete slabs, precast, tilt-up and concrete finish

Mesh Chair

  • Available heights – 1” / 2” / 2.5” / 3” / 3.5”
  • Mesh gauge: 3 – 10
  • 300 lbs. load bearing
  • Circular base will provide stability and support
  • Mesh chair is used for welded mesh and installed at four way crossing

Utility Chair

  • Available heights – 2.25” / 3.25”
  • Max bar size #4
  • Stable, light, economic and designed with 2 1/8” base
  • Used for slab work, precast and tilt-up

Rebar Chairs

  • Available Sizes:
  •     (RC-6-2) 6” width – 3” height - (RC-2-3) 12” width – 3” height 
  •     (RC-18-3) 18” width – 3” height
  • Max bar size #5
  • Eliminates tie wire
  • Dual clamping feature allows overlapping of rebar
  • RC-6-2 holds 2 pieces of rebar - RC-12-3 and RC-18-3 holds 3 pieces of rebar
  • Recommended spacing 4 feet

Spacer Wheels

  • Available sizes -  ¾” / 1” / 1.25” / 1.5” / 1.75” / 2” / 2.5” / 3” cover
  • Has double fastener that works with rebar and welded mesh, maintaining them to the center of the spacer
  • Minimal surface contact
  • Spacer Wheel used for walls, columns, beams, cast-in-place and prefabrication

Drill Shaft Wheel

  • Available sizes – 2” / 3” cover
  • Max rebar size #6
  • Lateral spacer, impact resistant for heavy and large structures
  • Provides guide system for reinforcement cages within caissons, drilled shafts and other construction applications

Plastic Stake

  • 18 inches long, used as a grade stake
  • Max bar size #5
  • 4 different locations for placement of rebar - 9” / 11” / 13” / 16 ½”
  • Recommended spacing 5 feet
  • Used in footings and other concrete applications

End Caps

  • Available sizes – CS075 #3, #6 bar and CS150 #8, #11 bar
  • Avoids possible knocks and scratches to workers in traffic zones
  • Used in horizontal applications